As the old adage goes, “necessity is the mother of invention,” and that is never more relevant than when working on a unique problem in deep water.
That’s the situation that Wright’s Well Control Services (WWCS) was facing in the Gulf of Mexico (GoM) in June while plugging and abandoning (P&A) a well in more than 300 m (1,000 ft) of water.
This was a riserless operation undertaken from the multiservice vessel HOS Achiever. DOF Subsea USA provided marine and subsea services.
What made the project unusual was the Dril-Quip wellhead, a one-of-a-kind piece of equipment, which would require innovation from start to finish. The wellhead had a subsea annulus monitoring flange at a 35° angle, pointing down. The flange needed to be removed to take returns and monitor the casing annulus during the P&A operation.
WWCS quickly discovered there were no off-the-shelf ROV tools that could perform those functions. The company needed to be able to nipple down on the old flange and nipple up on a newly installed flange – with all the work done subsea.
The concept for a new torque tool was developed, and the tool was designed and built. After the sub-base was removed, WWCS rigged up the new ROV torque tool to nipple down the flange at a 35° angle and nipple up the new flange with a 2-in. hot stab.
The next innovation was under way at the same time, with the company designing a new subsea connector that would allow the Dril-Quip tree-running tool (TRT) to remain subsea for the entire job. This step required a new hydraulic connector that would allow WWCS to engage and disengage a subsea BOP and lubricator – while leaving the TRT subsea – in case problems arose.
WWCS tested the TRT at its Lake Charles, La., facility. It was modified to include an emergency disconnect, a 15,000-psi fail-safe ball valve, and low-torque valves.
The third innovation was the modification of a Dril-Quip tubing-hanger pulling tool so tubing could be pulled using a crane subsea.
With all the tools designed, built, and tested, WWCS was ready to load the equipment on the boat for the P&A operation.
One of the vessel’s two moonpools was used to run the coiled tubing (CT) string and an umbilical, while using the other to pull the tubing and casing to the surface.
During the P&A operation, the company set six cement plugs and three cast-iron bridge plugs as well as cut and pulled 37 joints of 3 1/ 2 -in. tubing, 230 m (750 ft) of 9 5/ 8 -in. casing, 13 5/ 8 -in. casing, and 20-in. by 30-in. casing with a mechanical cutter below mudline.
The entire P&A operation was done in 30 days. In noting the innovation required, WWCS President David Wright, said, “We executed a very challenging subsea P&A utilizing four new subsea tools, including a jumper that we designed and built while on location.”
Recommended Reading
BPX Looks to Ramp US Production Over 60% by 2030
2024-05-16 - BPX Energy is looking to boost its U.S. production over 60% by 2030 as it considers bringing online a fourth processing facility in the Permian by mid-year 2025, Clark Edwards, the company’s vice president of development, said during SUPER DUG in Fort Worth.
Empire Petroleum’s Williston Drilling Program Identifies New Zones
2024-05-16 - Empire Petroleum provided updates on its Williston Basin development drilling program in its first quarter 2024 earnings results.
ConocoPhillips: Permian Basin a ‘Growth Engine’ for Lower 48
2024-05-15 - ConocoPhillips views the Permian Basin as a “growth engine” within its Lower 48 portfolio, the company’s Midland Basin Vice President Nick McKenna said during Hart Energy’s SUPER DUG event in Fort Worth.
Petrobras Not in a Race with Guyana to Boost Production, CEO Says
2024-05-14 - While Brazil and Guyana aren’t necessarily competing to see which country can produce more oil, Petrobras’ CEO Jean Paul Prates jokingly said Brazil was winning, while adding that Bolivia’s falling production was an opportunity for Argentina.
E&P Highlights: May 13, 2024
2024-05-13 - Here’s a roundup of the latest E&P headlines, with a couple fields coming online, as well as new contract awards.